WELCOME TO GoBlog!!!

Followers

Total Pageviews

Search This Blog

My Blog List

Pages

Tuesday, November 21, 2017

Konfigurasi 3 Switch Dan 2 Router di Cisco Paket Tracer Terbaru 2024

  November 21, 2017    





SWITCH 0


Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 30
Switch(config-vlan)#name pakeko (bisa diganti sesuai selera)
Switch(config-vlan)#exit
Switch(config)#vlan 40
Switch(config-vlan)#name masheru (bisa diganti sesuai selera)
Switch(config-vlan)#exit
Switch(config)#int fa0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 30
Switch(config-if)#exit
Switch(config)#int fa0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 30
Switch(config-if)#exit
Switch(config)#int fa0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 40
Switch(config-if)#exit
Switch(config)#int fa0/4
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 40
Switch(config-if)#exit
Switch(config)#
Switch(config)#exit
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa0/5
Switch(config-if)#sw mode trunk
Switch(config-if)#

SWITCH 1


Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#name oni (bisa diganti sesuai selera)
Switch(config-vlan)#exit
Switch(config)#vlan 20
Switch(config-vlan)#name afid (bisa diganti sesuai selera)
Switch(config-vlan)#exit
Switch(config)#int fa 0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#int fa 0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#int fa 0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 20
Switch(config-if)#exit
Switch(config)#int fa 0/4
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 20
Switch(config-if)#exit
Switch(config)#exit
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa0/5
Switch(config-if)#switchport mode trunk 

Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/5, changed state to up

Switch(config-if)#


SWITCH 3


Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vl
Switch(config)#vlan 10
Switch(config-vlan)#exit
Switch(config)#








Switch con0 is now available






Press RETURN to get started.












%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up


Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int fa0/3
Switch(config-if)#switchport mode trunk 
Switch(config-if)#ex
Switch(config)#ex
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#vlan database 
% Warning: It is recommended to configure VLAN from config mode,
  as VLAN database mode is being deprecated. Please consult user
  documentation for configuring VTP/VLAN in config mode.

Switch(vlan)#vlan 10 name oni (nama sama seperti di vlan 10)
VLAN 10 modified:
    Name: oni
Switch(vlan)#ex
APPLY completed.
Exiting....
Switch#vlan database 
% Warning: It is recommended to configure VLAN from config mode,
  as VLAN database mode is being deprecated. Please consult user
  documentation for configuring VTP/VLAN in config mode.

Switch(vlan)#vl
Switch(vlan)#vlan 20 name afid (nama sama seperti di vlan 20)
VLAN 20 added:
    Name: afid
Switch(vlan)#ex
APPLY completed.
Exiting....
Switch#
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up


ROUTER 0


Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.10.10 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int fa0/1
Router(config-if)#ip add 192.168.5.5 255.255.255.128
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#ex
Router(config)#int fa0/0.30
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.30, changed state to up

Router(config-subif)#
Router(config-subif)#encapsulation dot1Q 30
Router(config-subif)#ip add 192.168.30.33 255.255.255.240
Router(config-subif)#exit
Router(config)#int fa0/0.40
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/0.40, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.40, changed state to up

Router(config-subif)#encapsulation dot1Q 40
Router(config-subif)#ip address 192.168.40.49 255.255.255.240
Router(config-subif)#exit
Router(config)#

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 192.168.70.64 255.255.255.192 192.168.5.6
Router(config)#ip route 192.168.10.32 255.255.255.224 192.168.5.6
Router(config)#ip route 192.168.20.64 255.255.255.224 192.168.5.6
Router(config)#


ROUTER 2



Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa 0/1
Router(config-if)#ip add 192.168.5.6 255.255.255.128
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#int fa 0/0
Router(config-if)#ip add 192.168.70.65 255.255.255.192
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int fa 0/1.10
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/1.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.10, changed state to up

Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#ip add 192.168.10.33 255.255.255.224
Router(config-subif)#exit
Router(config)#int fa0/1.20
Router(config-subif)#
%LINK-5-CHANGED: Interface FastEthernet0/1.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.20, changed state to up

Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip add 192.168.20.65 255.255.255.224
Router(config-subif)#ex
Router(config)#

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 192.168.10.0 255.255.255.0 192.168.5.5
Router(config)#ip route 192.168.30.32 255.255.255.240 192.168.5.5
Router(config)#ip route 192.168.40.48 255.255.255.240 192.168.5.5


  No Comments

Tuesday, September 12, 2017

Perencanaan Pointing dengan Google Earth Terbaru 2024

  September 12, 2017    


1. Pertama download dulu Google Earthnya
2. ekstrak dan buka 


Tahapan Pelaksanaan

1. Cari letak rumah dan sekolahan dulu dengan search, kemudian kasih tanda dengan jarum kecil (pin).

2. kemudian dari rumah ke sekolahan beri tanda garis dengan klik bentuk pentagon , jangan lupa beri nama dari garis itu.

3. Setelah itu di gari itu yang ada di kolom klik kanan dan pilih "Tampilkan Profil Ketinggian" maka akan muncul seperti dibawah ini.


4. Kemudian di garis tadi dibagian kolom klik kanan dan properties dibagian pengukuran kita setting seperti dibawah ini.


5. Lalu dibagian Ketinggian setting seperti dibawah ini.


6. Kemudian masih di garis di kolom kita klik kemudian kita klik kolom atas yang bergambar penggaris kemudian kita letak kan di jarum bagian rumah ke jarum yg dibagian sekolahan, maka akan seperti dibawah ini.


7. Kemudian sebaliknya dari Sekolahan ke rumah kita maka derajatnya akan berbeda.


jika masih bingung bisa coment !!

  No Comments

Monday, September 11, 2017

TUTORIAL SETTING MIKROTIK Terbaru 2024

  September 11, 2017    



KONFIGURASI MIKROTIK CLI


  • Siapkan mikrotik, kabel lan dan komputer
  • colokan kabel jaringan ke ether 1
  • colokan kabel lan ke CPU dan ether 2
      Jika semua sudah ikuti langkah-langkah nya sebagai berikut :


1. Jalankan winbox, seperti dibawah ini ketik refresh sampai keluar ip dan klik lalu connect



2. Lakukan reset konfigurasi soft reset dengan cara 
     - klik system & reset configuration & centang no defaul

    

 - klik reset configuration & yes & sampai muncul tulisan router has been disconnect & klik ok







3. klik new terminal 






4. Membuat ip
    ipaddressaddaddress=10.10.20.28/24interface=ether1disabled=no (enter)
    ipaddressaddaddress=192.168.100.1/24interface=ether2disabled=no (enter) 
    ipaddressaddaddress=192.168.200.1/24interface=ether3disabled=no (enter)
    ( untuk mengecek ipaddressprint (enter)
    
    Membuat gateway 
    iprouteaddgateway=10.10.20.1 enter
    ( untuk mengecek gateway iprouteprint enter)
  




5. Membuat DNS 
    ipdnssetservers=10.10.20.1allow-remote-request=yes
    ( untuk mengecek DNS ipdnsprint enter)


    Membuat Nat
    ipfirewallnataddchain=srcnatprotocol=tcpout-interface=ether1 action=masquerade  enter


6. Ping Google dan cek Browsing




7. Membuat DHCP Server
   ipdhcp-serversetup enter , pilih interface yang ke ether tp-link / access point
(ether3), enter sampai :
address to give out : 192.168.200.2-192.168.200.254 diganti 192.168.200.2-192.168.200.100
kemudian di enter terus sampai selesai



8. Membuat Proxy 
    ipproxysetenabled=yescache-administrator=nama_peserta__absen_XIITKJ2 cache-on-disk=yes enter
(untuk mengecek proxy ipproxyprint enter)
ipproxyaccessadddst-host=*linux* action=deny
ipproxyaccessaddpath=*.mp3* action=deny
ipproxyaccessaddpath=*.mkv* action=deny
ipfirewallnataddchain=dstnatprotocol=tcpdst-port=80action=redirectto-ports=8080disabled=no




9.Memblock akses ke linux



10. Memblock akses ke .mp3


 11.Memblock akses ke .Mkv



12. Membuat Sntp
     systemntpclientsetenabled=yesprimary-ntp=62.201.225.9 / 203.160.128.3 (pilih salah satu)
systemclockset time-zone-name=Asia/Jakarta
systemclocksetdate=Oct/09/2017 time=09:00:00 (sesuaikan waktu)  enter
(untuk mengecek systemclock print)



13.Blokir / Membatasi Access Internet 
    ipfirewallfilteraddchain=forwardin-interface=ether3
time=7h-19h,sat,mon,sun,thu,tue,wed,fri action=drop (blok jalur ke access point)



 14.Reboot Mikrotik / System
    systemreboot enter


15.Block dan Membatasi Akses Internet


16.Ip Komputer




  No Comments

Subscribe to: Posts (Atom)